Description
GB464-UTP/D
Download Specifications
Download Instruction Manual
Download Related Article
Download Related TVI Article
Part Number: GB464-UTP/D
Title: GROUND-LOOP BLOCKER FOR UNSHIELDED TWISTED PAIR WITH DUAL VIDEO OUTPUTS
Category: CCTV
Industry: CCTV/Security,
Description:
The GB464-UTP/D operates with any standard CCTV, NTSC or PAL video signal.
The GB464-UTP/D device controls and corrects four channels of CCTV video, each channel is separately adjustable for Video Level and Picture Sharpness. A built-in active ground loop blocker removes the 60 Cycle Bars from the CCTV signal even after they have become part of the video signal. This ground loop isolator will prevent 60 Cycle “Hum Bars” from degrading your twisted pair wire CCTV system.
The Level control can be adjusted to overcome losses due to long wire runs up to 3000 feet, small wire gage or quality, and improper camera source terminations.
The Picture Sharpness control can be used to restore Picture quality to its original sharpness due to long wire runs, poor quality twisted pair wire or wire used in wet locations in twisted pair “Balun” transmission installations. It will also restore the video color-burst on a color camera to improve color camera operation on long wire runs.
This device will prevent Ghosting in the picture by absorbing and eliminating the reflected video Ghost signal. It will also restore the Characteristic Impedance of the down stream video signal to prevent secondary Ghosting in the picture.
An optional secondary 75 Ohm “BNC” connector video distribution output is included. This lets the installer add an extra monitor point or drive any other video equipment without affecting the original video signal.
By installing the GB464-UTP in your existing CCTV system you can avoid the many hours of troubleshooting and trial/error associated with problem installations. For some installations you will find it advantageous to install a GB464-UTP on each group of four channels. It is especially useful in installations requiring lightning protection. Lightening protection devices often induce 60 cycle bars into the video signal because they use a connection to ground that does not equal the video ground at the monitor.
If this product page shows “out of stock” the product is in production and can be purchased with a lead time of 1-2 weeks or less depending on quantity. To place an order for this product call 1-800-235-6960 and ask for the sales department. Or E-Mail your order to fmsystemsinc@sbcglobal.net. Most orders ship within a few days.
INPUT
Level, 1 Vpp, 140 I.R.E. Units
Impedance, 100 Ohms Balanced
Video Standard, CCTV, NTSC, PAL
Connectors, Screw Terminal
Video Channels, 4 Channels (A-D)
Power Requirements, +/- 12 VDC (RMS-400 Card-Cage)
Current, 100 mA
Card-Cage Requirements, RMS-400 Power Supply & Mainframe
PROCESSING
Clamping, Tip of SYNC
Common Mode Rejection, 40 dB Minumum
60Hz Rejection, 2 Vpp, Minimum Rejection
Video Gain, -2 to +7 dB
High Frequency Compensation, 0 to +29dB
RF Bandwidth, 30 MHz
OUTPUT
Level, 1 Vpp, 140 I.R.E. Units
Impedance, 75 Ohms
Connectors, BNC (Female)
Channels, 4 Channels (A-D)
Distribution Out (Optional), 4 Channels (E-H)
Signal to Noise Ratio, 70dB
COMMERCIAL OPERATING RANGE
Temperature Range, 0 – 50 Degrees Centigrade
Humidity, 95% Non-Condensing
MECHANICAL
Size, 1.00″ W X 4.87″ H X 10.00 L
RMS-400 REQUIRED CARD-CAGE
Card Slots, 9 Slots
Power Requirement, 24VAC 100mA Each
